Heavy Duty Screw Jacks Lifting Mechanism For Continuous Galvanizing Lines Roller Adjustment

Heavy Duty Screw Jacks Lifting Mechanism For Continuous Galvanizing Lines Roller Adjustment In Steel Industry, such as rolling mill rollers adjustment, steel mills roller adjustment, pipe mills roller adjustment, tube mills roller adjustment, roll forming mills roller adjustment, plate mills roller adjustment, powered feeder straightener rolls adjustment, synchronous coil feed lines rolls adjuster, adjusting precision leveler rollers, cold roller adjustment, hot roller adjustment, adjusting roll pass system. Compared with hydraulic roller adjustment system, screw jack roller adjustment has self-locking without brake or other locking mechanism, when electricity failure, attached loads will not creep, precision positioning, uniform lifting speed, complete synchronization, multiple units worm gear screw jacks system, easy operation and installation, maintainence free.

Heavy Duty Screw Jacks Lifting Mechanism For Continuous Galvanizing Lines Roller Adjustment Important Components:
1. Self-locking worm gear screw jacks.
2. Steel protective pipe cover for anti-rust and anti-dust upper worm gear screw jack base, when full retract stroke.

Heavy Duty Screw Jacks Lifting Mechanism For Continuous Galvanizing Lines Roller Adjustment Other Features:
1. Inverted type installation, tension load.
2. Heavy duty, precisely positioning, self-locking.
3. Translating screw or travelling screw with top plate end fitting.
4. Low speed gear ratio with gear reduction mechanism drive

Comments

Post a Comment

Popular posts from this blog

20 ton silo acme nut screw jack, 20t silo traveling nut screw jack, 20ton silo lifting nut machine screw jack for silo bolted storage tanks lifting in australia

Image
20 ton silo acme nut screw jack, 20t silo traveling nut screw jack, 20ton silo lifting nut machine screw jack for silo bolted storage tanks lifting in australia. 20 ton silo acme nut screw jack, 20t silo traveling nut screw jack, 20ton silo lifting nut machine screw jack are application in synchronized lifting storage bolted tank, such as big gas, oil chemicals, water, pelletts, cereals, biogas, liquid manure, silo, round reservoirs, caisson, crop storage bolted tanks. Compared with hydraulic lifting system, worm gear screw jacks have self-locking feature without brake or locking mechanism, precisely positioning, full synchronization, motor driven, easy installation and operation, maintenance free. Each screw jack which support 2.5 ton load panels, travel stroke 1500mm, 20pcs worm gear screw jacks, low lifting speed, silo storage bolted tank application, outdoor ambient. 20pcs worm gear screw jacks and 1pc gear reducer, upright type worm gear screw jacks mode
Read more

Fabrication and Design Low Backlash Reverse Worm Screw Jacks, Anti Backlash Mechanical Lifting Jacks, Anti-Backlash Screw Jacks, Anti-Backlash Mechanical Actuators, Anti-Backlash Worm Drive Lifting Jacks

Image
Anti-Backlash Screw Jacks Screw jacks are used for positioning loads in numerous applications, however when the load direction alternates between tension and compression within the operating cycle and a high position accuracy must be maintained then a specific type of screw jack is required. The Anti Backlash Machine Screw Jacks is recommended for such applications, as it is able to reduce the axial backlash between the lead screw and the trapezoidal screw thread in the gear to a practical minimum. Axial backlash exists in standard screw jacks as the "gap" or "play" between the flanks of the lead screw thread and the internal thread on the worm gear nut. This gap or play is due not only to normal manufacturing tolerances, but to the fact that there must be some clearances to prevent binding and galling when the screw jack is operating under load. In most applications either the load direction is constant so axial backlash does not occur or the position error
Read more

Hand Operated Upright Rotating Machine Screw Actuator 5Ton And 2963MM Long Acme Screw And Acme Nut For Conveying Rails In Rail Train In South Africa

Image
Hand Operated Upright Rotating Machine Screw Actuator 5Ton And 2963MM Long Acme Screw And Acme Nut For Conveying Rails In Rail Train In South Africa. 1. Upright Rotating Machine Screw Actuator 5ton fitted on base with special dimensions bronze travelling nut. 2. 2963mm long shaft with 2763 mm ACME thread Part of end not threaded at both ends will require diameter 19. Thrust bearings at both ends of horizontal screw. Both items require simular ends (16x16mm square x 30 mm long) 3. Machine Screw Actuator Load Capacity in general = 5000kg maximum 4. Traveling speed is by hand, however maximum travel per turn possible will be important. 5. The equipment is used on a rail train that conveys 48 of 60kg/m rails of 240 meters long. Offloading takes place two rails at a time. 48 Rails can be offloaded in one day. Offloading of 48 rails can happen up to about four times per week and continue almost whole year long. 6. Working conditions it typically South African w
Read more