Four Screw Jacks Lifting Platform Assembly Drawings And Installation Instructions In Singapore


Four Screw Jacks Lifting Platform Assembly Drawings And Installation Instructions In Singapore


 Singapore customers 4 screw jacks lifting table includes 4 pieces JTW-10T upright rotating screw jacks with bronze travelling nut, 1 piece JTP140 1:1 ratio right angle miter gear box 3 way, 2 pieces JTP140 1:1 ratio right angle miter gear boxes 2 way, 13 pieces FL28/38 steel jaw couplings, 4 pieces flange type road bearings, 6 pieces linking bars, 1 piece electric motor.

 Suggestions When Assembly Screw Jacks Lifting Table
1. The foundation for the screw jack should be rigid enough to maintain correct alignment with connected machinery and have sufficient strength to support the maximum load.
2. It is extremely important that the screw jack be installed so that the lifting screw is perfectly plumb and all connecting shafts are aligned with the worm shaft.
3. After precise alignment, each member must be securely bolted and if possible doweled in place. Doweling will assure exact repositioning if ever removed. It is essential that a gear unit be securely bolted down to the foundation using bolts of proper diameter to fit the mounting holes.
4. After the screw jacks, linking bars, couplings, right angle miter gear boxes and electric motor are coupled together and aligned in a system, there should be no signs of binding or misalignment.
5. The foundation of the screw jack is critical to insure alignment. Mount the jack and check that the axis of the lifting screw is parallel to the movement of the load and centered with respect to the load. Shim under the base to achieve this if needed. Both eccentric load or side load will cause premature wear and possible bending and failure of the screw jack. Once the alignment is correct hand tighten the mounting bolts.
6. The next step is to align the input shaft with the worm shaft of the screw jack. This alignment can be just as critical to proper operation. Test the alignment by rotating the shafts by hand and fully extend the lifting screws.
________________________________
Jacton Electromechanical Co.,Ltd
Chang An,Dongguan,Guangdong,China
Phone: 86 769 81585852
Fax: 86 769 81620195
Mobile: 86 135 32830851
Skype: jactonjack
Email: sales@screw-jack.com
Web: http://www.screw-jack.com
________________________________
Our Advantages:
1. Only for lifting solutions, only for jacks, gear boxes, complete lifting system with all accessories.
2. International standard materials like bronze worm wheel, heating treatment worm shaft s45c, acme screw s45c.
3. Pay more attention axial play & radial play, ensure jacks long service life.
4. Standard 1 year warranty, any defects from our sides, after us confirmed, free for replacements.

Comments

Post a Comment

Popular posts from this blog

20 ton silo acme nut screw jack, 20t silo traveling nut screw jack, 20ton silo lifting nut machine screw jack for silo bolted storage tanks lifting in australia

Image
20 ton silo acme nut screw jack, 20t silo traveling nut screw jack, 20ton silo lifting nut machine screw jack for silo bolted storage tanks lifting in australia. 20 ton silo acme nut screw jack, 20t silo traveling nut screw jack, 20ton silo lifting nut machine screw jack are application in synchronized lifting storage bolted tank, such as big gas, oil chemicals, water, pelletts, cereals, biogas, liquid manure, silo, round reservoirs, caisson, crop storage bolted tanks. Compared with hydraulic lifting system, worm gear screw jacks have self-locking feature without brake or locking mechanism, precisely positioning, full synchronization, motor driven, easy installation and operation, maintenance free. Each screw jack which support 2.5 ton load panels, travel stroke 1500mm, 20pcs worm gear screw jacks, low lifting speed, silo storage bolted tank application, outdoor ambient. 20pcs worm gear screw jacks and 1pc gear reducer, upright type worm gear screw jacks mode
Read more

Hand Operated Upright Rotating Machine Screw Actuator 5Ton And 2963MM Long Acme Screw And Acme Nut For Conveying Rails In Rail Train In South Africa

Image
Hand Operated Upright Rotating Machine Screw Actuator 5Ton And 2963MM Long Acme Screw And Acme Nut For Conveying Rails In Rail Train In South Africa. 1. Upright Rotating Machine Screw Actuator 5ton fitted on base with special dimensions bronze travelling nut. 2. 2963mm long shaft with 2763 mm ACME thread Part of end not threaded at both ends will require diameter 19. Thrust bearings at both ends of horizontal screw. Both items require simular ends (16x16mm square x 30 mm long) 3. Machine Screw Actuator Load Capacity in general = 5000kg maximum 4. Traveling speed is by hand, however maximum travel per turn possible will be important. 5. The equipment is used on a rail train that conveys 48 of 60kg/m rails of 240 meters long. Offloading takes place two rails at a time. 48 Rails can be offloaded in one day. Offloading of 48 rails can happen up to about four times per week and continue almost whole year long. 6. Working conditions it typically South African w
Read more

Fabrication and Design Low Backlash Reverse Worm Screw Jacks, Anti Backlash Mechanical Lifting Jacks, Anti-Backlash Screw Jacks, Anti-Backlash Mechanical Actuators, Anti-Backlash Worm Drive Lifting Jacks

Image
Anti-Backlash Screw Jacks Screw jacks are used for positioning loads in numerous applications, however when the load direction alternates between tension and compression within the operating cycle and a high position accuracy must be maintained then a specific type of screw jack is required. The Anti Backlash Machine Screw Jacks is recommended for such applications, as it is able to reduce the axial backlash between the lead screw and the trapezoidal screw thread in the gear to a practical minimum. Axial backlash exists in standard screw jacks as the "gap" or "play" between the flanks of the lead screw thread and the internal thread on the worm gear nut. This gap or play is due not only to normal manufacturing tolerances, but to the fact that there must be some clearances to prevent binding and galling when the screw jack is operating under load. In most applications either the load direction is constant so axial backlash does not occur or the position error
Read more